YOUR COMPLETE TUTORIAL FOR INSTALLING A BATHTUB

Your Complete Tutorial for Installing a Bathtub

Your Complete Tutorial for Installing a Bathtub

Blog Article

Services

How do you really feel with regards to Tools You Need to Install a New Bathtub ?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a tub isn't exactly rocket science, but it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult project. If the old bathtub is conveniently obtainable, the project can move rapidly; if you have to open a wall surface to eliminate the old tub and also position the brand-new tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the new one. See to it you have certified on your own for the job as well as fit trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will assist you mount a new tub in your bathroom if you have actually currently purchased a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your tools as well as material checklist should consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the case.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
    Before going on to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existent supply pipes.
    If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, position the tap in the placing opening in the bath/basin making certain that the washing machines remain in area in between the tap and the sink. Secure the faucet in position with the producer provided backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

    Mounting the Tub


    Making use of the two wood boards under its feet, place the bathtub in the called for placement. The wood boards are useful in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four tiny points.
    The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reads degree.
    To set up taps, fit the bottom of the furthest versatile faucet port to the proper supply pipeline by making a compression join; then do the same for the other tap.
    Activate the water supply and examine all joints and also new pipework for leaks and tighten them if essential. Load the tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
    Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub needs to wait up until the bathtub has actually been used at the very least once as this will certainly settle it into its last setting.

    Planning for the Setup


    To start with, the supporting framework provided with the bath must be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to prevent stress on the bath tub.
    Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.

    Tiling Around the Tub


    In the location where the bathroom meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, causing problems with moisture and possible leaks to the ceiling listed below.
    You can choose from a range of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and also cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not think about this activity prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    We were made aware of that report on How to Install a Bathtub from a friend on a different blog. So long as you enjoyed reading our blog post plz remember to pass it around. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Damage control? Ring!

    Report this page